Our regular 700 Series – the heart of Ever-Power quickness reducer products – has been serving industry reliably for over a decade. Its proven modular design has set the industry standard for performance and may be the most imitated item in the current worm gear acceleration reducer marketplace. But why settle for a knock-off when you can have the original – from Ever-Power.
Specifications
11 basic one reduction sizes
8 basic double reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow output shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow output bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in share)
Product Features
The 700 Series’ huge oil reservoir provides efficient heat dissipation and lubrication for longer operating existence.
Its multi-position mounting versatility allows for installation in virtually any position.
Housings are straddle-milled, best and bottom level, for precise alignment of horizontal and vertical bases.
Internal baffles assure positive, leak-free venting.
The 700 Series’ rugged housing, fabricated of fine-grained, gear-quality cast iron, provides optimum strength for optimum durability, and also greater precision during worm and gear alignment.
Ever-Power 700 Series high-strength bronze worm equipment is straddle mounted between heavy-duty tapered roller bearings to improve thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel result shaft assures convenience of high torque and overhung loads.
Pipe plugs allow easy fill, level, and drain in any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal existence.
Both 2D and 3D CAD drawings are available in our eCatalog.
Ever-Power worm gearboxes have earned a status to be an industry benchmark worldwide. Our achievement came from our relentless drive for quality with state-of-the-art technology, all and will be offering worm gearboxes are inexpensive prices. High versatility accorded through a wide choice of mounting choices, shaft configurations and electric motor interfaces, makes the Ever-Power worm gearbox the default choice for the industry. The helical-worm and the double-worm edition, with or without the torque limiter, add up to the advantage, creating a highly versatile drive system.
Ever-Power Worm gearboxes provide high torque with low speed gear ratio. Being simple and compact in design, these gears can perform higher gear ratio than the helical gears. These worm reduction gears having screw type qualities are similar to helical gears, but its helix angle is typically comparatively bigger) and its body is generally quite lengthy in the axial direction. The gears in these gearboxes can be right or left-handed dependant on the purpose.
Mounting choice include universal housing, aspect flanges, foot (horizontal and vertical), shaft mounted with torque arm. Obtainable in Solid shafts (one or dual), with torque arm or torque limiter.
Worm reduction gears features
Principles
A worm gear is a type of interlocking gear made up of a worm shaft and worm wheel. The worm is usually shaped just like a screw and the worm wheel is definitely a kind of gear machined to get a tooth profile with the same configuration.
The procedure of a worm gear is comparable with that of a bolt and nut. The principle is the same as a nut that has been fixed so that it cannot rotate and therefore progresses in the axial path when the bolt can be turned.
The design of a worm gear is considered through the relationship between your rack and spur gear on the middle plane of the worm wheel.
Features
High reduction ratio One rotation of the worm rotates the worm wheel by one tooth. Due to this, in a 1 speed decrease gears, the wheel could be manufactured so that it’ll be rotated 1/60 (1/120 in unique applications).
Orthogonal shaft The shafts are aligned orthogonally because of the structure. This feature can help you layout the turning transmitting direction at the right angle.
The arbitrariness of the rotation direction The screw direction of the worm could be clockwise or counterclockwise (generally clockwise). It is possible to change the rotation path of the worm wheel by changing the screw path.
A multitude of shaft layouts The wide variety of shaft layouts is one of the features of interlocking gears.For example, right shaft output, remaining shaft output, dual shaft input and dual shaft output, etc., combine for a total of 14 types (Figure 2) and, if attachment orientations are included, it is possible to pick from over 40 layouts.
Low noise, low vibration The interlocking of the worm and worm wheel is certainly characteristic because the contact is linear and the relative slide is fantastic. In comparison to rolling power transmission, sound and vibration are extremely low. For this reason, this technology can be used to drive medical gear, elevators and escalators, etc.
The primary specifications of worm reduction gears
MA Series(Small)
Center distance(mm) 32,40
Reduction ratio 10,20,30,40,50,60
Input capacity(kW) 0.1~1(at an input of 1800 rpm)
Output torque(N・m) 20~66
Input speed(rpm) 0~1800
MA Series(Medium)
Center distance(mm) 50,63,80,100,125,140,160
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.4~30(at an input of 1800 rpm)
Output torque(N・m) 900~3570
Input speed(rpm) 0~1800
S Series
Center distance(mm) 50,60,70,80,100,120,135,155,175,200,225,250,300,350,400,450,500
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.3~255(at an input of 1800 rpm)
Output torque(N・m) 50~56600
Input speed(rpm) 0~1800
Key points when choosing a worm reduction gears
Selection
When selecting a worm reduction gears, the procedures for selecting the right gear are described in the manufacturer catalogs and the series and models should be selected according to those procedures. Particular care should be taken in key areas such as for example selecting the strain index, calculating the overhang load and examining heat rated capability from the manufacturer.
Cautions during use
When utilizing a worm decrease gears, the heat produced during the initial period of use is high and running-in operation at 1/4, 1/2 and 3/4 of rated torque for eight hour periods is paramount to sufficiently attaining the performance of the worm decrease gears.
Maintenance and inspection
After completing running-in operation (approximately 50 hours), it is necessary to change the lubricating oil and to change the lubricating oil after that about 1 time per year according to the operation manual provided by the manufacturer.
Product Description
The Worm Decrease Gear Box is provided by our company is of high-quality. Our products are created by using premium quality material and enhance technology at our vendors end. These are widely used in a variety of sectors. Our products are often available at an extremely low market prices.
Motor Mount Frame Options
TEC Motors, worm reduction gearbox.
Option A-160 B5 Body, Flange Mount.
Option B-132 B14 Frame, Face Mount.
Option C-100/112 B5 Frame, Flange Mount.
High efficiency and safe operation. High load capacity and overload functions. Result Torque = (Power (kW) x 9550 (Constant))/ Gearbox output speed (rpm).
Higher ratios available on request reliant on service factor (40:1, 50:1, 60:1, 80:1, 100:1)
DESCRIPTION
Wormgears of the VF series are milestones for the market worldwide. They succeeded in merging uncompromising quality with stateoftheart technology amd renown price effectiveness.Absolute flexibility is given by the wide choice of several installation options, shaft configurations and motor interface, all offered as standard. The helicalworm and the doubleworm edition, with or without the torque limiter, also accumulate, creating a highly versatile drive system.
ADDITIONAL INFORMATION
AMP
0.42 A
EFFICIENCY
84%
HP
0.12
KW
0.09
RATIO
7
RPM
200
TEMPERATURE RATING
20 degree C TO 80 level C
TORQUE
4 Nm
HSN
8483.40.00
WARRANTY PERIOD
12 Months
The worm reduction gears can be found in two series: X and H.
The series X, having a worm and worm wheel set, is available in versions XA with shaft and XF-XC with mounting provisions for motor.
Version XF (bell housing + coupling) offers great versatility to suit a broad range of applications and higher efficiency than the compact collection XC, where in fact the emphasis is on space efficiency.
Series H offers the same features because series X with an added plus: a spur gear pre-stage at the input end provides higher efficiency and a broader range of ratios compared to the X series.
Body sizes 110 and 90 feature a cast-iron housing cast enbloc, whereas smaller sizes make use of die-cast aluminium housings. The worm shaft is manufactured from casehardened and hardened alloy steel and ground-finished.
The worm wheel has a cast iron hub with cast bronze insert. Hollow result shaft is supplied as standard.
Broad range of options available:
second input, output flange, single or double extension result shaft, torque limiter with through cable, torque arm.